Smart Energy Management for Marine and Off Grid

Category: Sensors

Sensors

Showing all 9 results

  • WS500-BT-K Battery Temperature Sensor Cable

    $39.95$64.95

    Fifteen-foot tinned cable with 2-wire waterproof connector (attaches to regulator wiring harness) and tinned temp-sensor lug. This sensor can be added for battery centric configurations where you want to monitor the battery bank temperature and use the signal to reduce the output of the alternator. These parameters can all be set in the regulator using the configuration tool.

    Select options
  • Barometer YDBC-05

    $99.00 $89.10

    The Barometer is intended for measuring atmospheric pressure within the range from 300 to 1100 hPa (mbar). The sensor is located inside the device case. Many chartplotters and digital navigation instruments are able to display data on pressure in the form of graphs or show a trend indicator; this allows tracking of trends in the weather change. The Device dimensions, including the connector, are 54x20x20mm, the mass is only 11 grams, so it is suitable for racing yachts. Pressure data output resolution 0.01 hPa (mbar), absolute measurement accuracy is ±1 hPa, relative measurement accuracy is ±0.12 hPa.

    Select options
  • Current Shunt 500/50

    $59.95 $47.95

    This shunt works well with the WS500 to provide either battery or alternator current flow feedback.

    Add to cart
  • Humidity Sensor YDHS-01

    $149.00 $134.10

    Provides chart plotters and instrumental displays with humidity and air temperature measurements and calculated dew point temperature. High quality sensor with ±2 % RH and ±0.3 °C accuracy in most of the operating range. The device is plug and play; you only need to plug it into a NMEA 2000 backbone to get readings on all chart plotters and instruments on board.

    Select options
  • Thermometer YDTC-13

    $99.00 $89.10

    The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F), the sensor is placed outside the case on a flexible, 95cm wire in a sealed stainless steel sleeve and can be used to measure the temperature of gases or liquids. If necessary, the wire can be elongated up to 100 meters. The Thermometer can be configured by the user to display data as “Air temperature”, “Sea temperature”, “Temperature in the refrigerator”, “Temperature in the engine room”, “Bait Well Temperature”, etc.

    Select options
  • Tank Adapter YDTA-01

    $149.00 $134.10

    NMEA 2000 adaptor allows you to connect an existing resistive type fluid level sensor (EU, US, JP or custom) installed on a tank and display the fluid level on NMEA 2000 devices, including chart plotters and instrumental displays. The Adaptor can be configured to report one of the seven fluid types defined in the NMEA 2000 standard: Diesel Fuel, Gasoline Fuel, Oil, Fresh Water, Waste Water, Black Water (Sewage), or Live Well. Can be installed as a standalone measuring device or in parallel with an existing analog gauge or Volvo Penta MDI.

    Select options
  • Exhaust Gas Sensor YDGS-01

    $149.00 $134.10

    The Sensor measures the temperature of extremely hot gases, solids and liquids within the range from 0 to +800 °C (+32 to 1472 °F). The Sensor can be configured by the user to display data as “Exhaust gas temperature”, “Air temperature”, “Heating system temperature”, “Engine room temperature”, etc. The Device is plug and play; you only need to plug it into a NMEA 2000 backbone to get readings on all chart plotters.

    Select options
  • REC Q BMS Temp. Sensor

    $24.95

    Temperature sensor for use with REC Q series BMS units

    Add to cart
  • Rudder Adapter YDRA-01

    $149.00 $134.10

    The NMEA 2000 Rudder Angle Adapter YDRA-01 allows you to connect an existing resistive type rudder angle sensor installed on a rudder and supply NMEA 2000 autopilots, chart plotters and other devices with the rudder angle. Can be used with a rudder angle sensor with maximal resistance less than 400 Ohm, including EU or US standard sensors, and with 0-5V voltage output sensors. The Adapter can work in parallel with an existing analog gauge.

    Select options
x Logo: Shield
This Site Is Protected By
Shield